Vehicles
32 not categorized PORSCHE 911 SIDE SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91450107510 Just pulled up on the 914 emergency brake handle and it broke off in your hand? The pivot stand has rusted away! Years of hardtop side seal leak directly onto this complex part has caused the problem. Discontinued by the factory in 2001 this identical part is an easy installation after simply sliding out the drivers seat and removing the seat rack and rocker carpet. This part can then be spot welded in. View/Change Diagram
$68.90
Make a selection 91450182510 S shaped channel to hold the engine bay seal on the passenger or drivers side easily spot welded into place. is included with the engine shelf replacement. make sure that you order a new engine bay seal for this part while you are at it! View/Change Diagram
$38.00
Make a selection 91451231711 This is the large u shaped rear trunk seal that fits around the rear three sides of the rear trunk and seals it from the elements. make sure you check the tail light bodies to rear panel mounting for water leaks before suspecting the rear trunk seal to leak. also check the alignment of the trunk hinges and their pivot cups. View/Change Diagram
From $82.00
Make a selection 91179950307 This seal sits on the trailing edge of the front fender at the top just below the windshield. Sold individually. 2 necessary per car. Driver's or passengers side fitment. View/Change Diagram
From $6.29
Make a selection 91453182110 The "b" part is an excellent reproduction of the original seal. The r and g are originals. this is the seal that fits on the unibody between the rocker carpet and the threshold, this assures a good door seal and no rattles! slightly smaller than the original it is easily installed with a plastic hammer (or a strong heel of the hand!) order the corresponding seal on the door for the tightest fit. View/Change Diagram
From $37.10
Make a selection 91450415510 A must have part for engine cooling. replace this part when the engine is out and clean the bay at the same time! this part is for the drivers and passengers side only check all engine sheet metal boots and seals while you are at it for the best cooling. View/Change Diagram
From $19.00
Make a selection 91463196010 This is the perfect aesthetic upgrade for your 70-76 914. replace your old red and cracked usa lenses with these gorgeous italian lenses reproduced to the smallest of detail. italy is the home of gorgeously soulful design, so Porsche had to spice up the 914 to sell them in italy. they were sold from the factory with clear taillight lenses, front turn signals, and side markers. order all three for your own little slice of italy! General Fitment914 1970-76
$249.50
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection 92835194100 Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to get hot? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper! View/Change Diagram
From $20.90
Make a selection 944185072 Please specify year of car when ordering. General Fitment944 1989-91944 1985-88 944 1982-85
$587.79
Make a selection 94455732100 Known as: rubber seal / rubber seal side window View/Change Diagram
$62.52
Make a selection 96454303502 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Driver's side fitment.
From $90.50
Make a selection BES99101260S - + 20 crank hp & + 14 crank torque. - 200 cell hjs tri-metallic "hd" cats. - 2 tubing (50 mm) with motorsport merge collector. - weighs 18.5 lbs. (8.4 kg). - 1.5 lb (9.1 kg) saving's over OEM header. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - works with OEM sealing rings and clamps. See below for part numbers. - made in Germany. - reduces thermal load and backpressure to for more torque in the mid-range and hp on the top end. Be sure to add new clamps and sealing rings to your order. 2 qty. Clamps are needed, they are part # 99711133690 and 2 qty. Sealing rings are needed, they are part # 98011156100. Our latest development for the GT3 is aimed at those who are looking fo...(choose a part on the right to read more)
$5,286.60
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection AA500A Our rubber kits are for the perfect restoration. Available only from Automobile Atlanta, this kit consists of everything we use in our restoration shop. General Fitment914 1970-76
$1,012.23
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FA500958 The new fortune auto generation 5 internal floating piston is considerably lighter and uses a low-drag teflon band that drastically reduces stiction. This allows the damper to react quicker to shock forces. The fortune auto 500 series damper shaft seals have 40% less drag than our previous models. This provides for less hysteresis and for superior control of driver inputs. Our new seals are made of a specially formulated buna rubber compound that provides a great balance between reliability and performance! Since the shaft seal is the most important seal on the shock, a stronger seal will greatly improve quality and performance.shims are deflection disks that cover up the port holes on a piston. They regulate t...(choose a part on the right to read more) General FitmentCAYENNE 2011-14
$1,956.15
Make a selection 99905304104 High quality, European made, sealed angular contact bearing. This number is superseded from 999 053 041 01, 999 053 041 02 and 999 053 041 03. Sold individually. Left or right side fitment. Please note: this is the front bearing for the 964 / 965 / 993 and 996 models. It is the front and rear bearing for the 986 models. View/Change Diagram
From $42.00
Make a selection 91511608705 On the flywheel side, the guide tube facilitates the movement of the thrust bearing in order to engage / disengage the clutch. On the gearbox side it provides a seal between the gearbox and driveshaft. These two functions are critical, so we recommend replacing the guide tube with any thrust bearing or clutch replacement. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $115.01
Make a selection FVD721T251 This special service tool was developed for the proper installation of oil seal on pulley side of crank shaft. Trying to do this task with any other method is risking a total engine failure by way of a damaged oil seal. Applicable: Porsche model - 996 & Boxster.
$129.80
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection FVD721T34C Oil seal arbor tool necessary for the installation of the oil seal on the pulley side of the crank shaft.
$93.50
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection GR0890100 Suitable for bonding rubber mouldings to polished, primed or painted metals, wood, various plastics, etc. General FitmentACCESSORY
$29.99
Make a selection PCG53160100 This is the seal behind the door latch base. Made of nylonized rubber, this seal will never shrink or split. Sold each, fits left or right side. View/Change Diagram
$4.77
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |